Trip to Blake Island

Sail track for Blake Island trip.

Since buying Fantasia, our Catalina 22, in the summer of 2014, we've spent the majority of our sailing time in the northern part of Lake Washington, close to moorage with the safety and comfort of protected waters. Since we didn't have a functional steaming light, we never stayed out beyond dusk and just focused on having fun close to home and learning how to take care of our boat and operate safely around other craft. This season, many of the upgrades we chose to work on were those that would enable us to be on the water after dark, whether sailing, steaming or anchored, and to begin visiting other nearby locations in Puget Sound.

We went out on our first overnight trip on Fantasia. We chose a relatively close location, Blake Island, as our first destination. There were many firsts on this trip; our first time through the Hiram M. Chittenden Locks (a.k.a. Ballard Locks), our first sail in Puget Sound, our first overnight stay at a State Park marina, and our first overnight stay on the boat. It was a chance to really test all our new electrical upgrades, both AC and DC. The chart plotter enabled us to accurately determine where we were in relation to shipping and ferry lanes.

We headed out on Saturday morning, pulling away from the dock about 9:40 AM. headed towards the locks under motor. We wanted to get to the locks as early as possible, as we'd heard many stories about how busy the locks get on a nice day and the long the wait to get through them. Although we had been as far as Lake Union twice before, this was our first time continuing beyond it.

Along the way, there are seven bridges that we need to pass under, but given our mast height, we only are concerned about the Fremont Bridge. The clearances on all of the other bridges at the center are well beyond our masthead at 29.1 feet (plus our VHF antenna) above water level. However, the Fremont Bridge, at only 30' is a concern for a Catalina 22 with antenna and anchor light. The water level in the lakes varies up to two feet throughout the summer boating season, so we can pass under this bridge when water levels are exceptionally low. We passed under slowly, but the very tip of our (flexible) VHF whip antenna brushed the bottom of the bridge in one spot. At higher water level, we could not have made it. Due to this low clearance, the Fremont Bridge opens on average of 35 times per day making it one of the most frequently opened bridges in the United States. On the way back, we decided it was better to have the bridge opened for us.

The Fremont and George Washington Memorial bridges after
we motored past them on the way to the locks.

Bridges from East to West. Refer to NOAA chart 18447 for more information on bridge heights and other information.

Montlake Bridge

University Bridge

Ship Canal (I-5) Bridge (fixed)

George Washington Memorial (Aurora) Bridge (fixed)

Fremont Bridge

Ballard Bridge

Burlington Northern RR Bridge

We arrived at the Ballard Locks at 11:40am, behind a half dozen or so other boats jockeying for position to get into the currently loading large lock. There are two continuously operating locks, one large and one small. We decided to get in line for the small lock, which had just closed with a full load of boats heading out, rather than hope to get a spot in the currently loading large lock. We tied up to the waiting area on the north side. The small lock turned out to be the better choice, especially for a first time through the locks.

Tied up waiting to go through the small
lock.

With fewer boats to load, tie, untie and unload, the small lock cycles through much quicker than the large lock. In the small lock, the tie down points are on floats that move with the boats and the water level, so tying up and managing lines is much easier in the small lock. Going through the large lock, you must have two 50' lines with eyes and must play out or take in the lines as the water level changes, whereas with the small lock, 25' lines will suffice, and they do not have to be managed while the water level changes.

We had to wait about 35 minutes for one full cycle of the locks in each direction. While waiting for the lock, we were entertained by jumping salmon, which had recently exited the fish ladder, and a very mischievous seal who had also decided it would be fun to travel through the locks along with the boats. Finally it was our turn to load.  It took about 15 minutes to get through the lock, including getting tied up and cycling the lock. Kudos to the locks staff; they gave friendly direction throughout the process making it a relatively stress free experience.

In the small lock, waiting for it to cycle.

We motored the remaining way out of the ship canal. By 12:40 we were away from land and out in beautiful Puget Sound. There is a lot more space on Puget Sound than Lake Washington, so although there are many boats around, they aren't likely to be passing nearly as closely, or nearly as frequently as the do on the lake. There is a lot of room to maneuver, and most of the boaters take advantage of that fact.

One of the most surprising things about being out on Puget Sound was how little we were impacted by wake. In the confines of Lake Washington, on any nice boating day, the surface of the lake gets worked up into a frenzy from all of the power boats and jet skis. This is not the case in Puget Sound. The wakes are few, mainly generated by the occasional ferry or container ship passing and those provided mainly a gentle rolling lift and fall.

Using our new chart plotter, we determined our desired heading and raised sail. The wind was blowing from the North-Northeast, perfect for a run South towards Blake Island. Winds were very light, but thankfully the current was with us. We ran southwards wing and wing for a while, then decided to furl the Genoa and raise the asymmetrical spinnaker.  As we made our way south, the Seattle skyline came into view. Ferries bustled back and forth, moving cars and people from the mainland to Bainbridge Island or Bremerton and back. Container ships came and went, as did various tugboats. Three cruise ships could be seen on the Seattle waterfront, preparing to head for Alaska. The winds were light, and we only traveled between two and four knots.

Blake Island to the port, gennaker flying, ferry ahead.

While sailing, we had the VHF radio working for the first time with the new wiring and antenna. We listened in as three separate boats called the Coast Guard for help. One had run out of fuel in Puget Sound somewhere. Two others were also disabled, near Anacortes  and Camino Island. We hope to never need that kind of help.

We arrived at Blake Island simultaneously with two other sailboats at about 4:30 PM. We all dropped sail and jockeyed to get into the dredged passage to the docks, having to make way for the Argosy Good Times II to come out. We got in first and found that they had 30' of dock space left...just enough for one Catalina 22. The boats behind us had to settle for mooring buoys that surround the island, which actually would have been problematic for us since we do not have a dinghy. There is a couple that acts as volunteers running the harbor, helping to tie up, and giving the rundown on how things work.

Moorage at Blake Island is $0.70 a foot, plus $6 for shore power, per day. You pay at a pay station on shore. There are bathrooms with running water. Hot showers are available for $0.50 for three minutes by getting tokens from a machine at the ranger station. The ranger station also has a store that is open for three hours a day for essentials such as sodas and snacks. We checked on the Tillicum Village evening performance, but it was full. (More on this in a bit.) After thinking on it a bit, we decided to see the show on Sunday and leave in the afternoon.

Seattle from Blake Island,
the entrance to the moorage in the foreground.

Blake Island is a 475 acre state park, and the only access is by boat. There are tour boats from Bremerton and Seattle that come out for the Tillicum Village performances, that can also be used as a ferry. Otherwise, the only way to the island is by private boat. It is wooded, with hiking trails. There are three areas to camp on the island. Raccoons abound, and they are aggressive about getting into food. No food must be left accessible on deck or in unprotected areas. If you are moored away from the dock, beware that the raccoons can swim and still get to any unprotected food. There are also deer on the island, but they are not nearly as aggressive.

We settled in for the evening, putting a new 8'x10' tarp over the boom for shade, as well as the pop-top curtain. The curtain (which is actually made of vinyl) encloses the cabin with the pop-top up, giving more head room when docked, as well as gives a zipper opening instead of needing to put in the crib boards when closed up. It also gives shelf space next to the mast below the pop-top, but inside the pop-top that allows repositioning some of the stuff that is not needed.We hooked up to shore power, using our AC wiring. This allowed us to recharge the batteries consumed by the interior lights, recharging devices, VHF, and chart plotter.

Blake Island trail.

We made reservations for the Sunday performance at Tillicum Village, then went for a short walk across the North of the island. There are well tended wide trails, under a Douglass fir canopy. You can see Mount Baker to the North, Seattle to the Northeast, the Olympics to the West. Mount Rainier is to the East of the island. After the walk, we sat in the cabin and played cards until bed time. Taylor decided to sleep in the cockpit, which she later regretted, since it got cold. The wind kicked up during the night, but was still by morning.

During the night, the tide had fallen. Two small power boats that had tied up to the shore were left high and dry on the beach. They eventually were pushed back into the water. We were reminded to keep in mind the tides for future trips, which we do not worry about in the lake.

Fantasia tied up to the left, the family in the center, and note
boats to the right.

The same boat the next morning.

In the morning, we ate breakfast on the boat, and went for a short walk on the East side of the island. There are wonderful views of Seattle and Mount Rainier. We made the boat ready to head home. We paid for another day of moorage (but not power), as check out time is 1 PM, and the Tillicum Village performance concluded about 2 PM.

Tillicum Village is a Native American long house where they cook salmon using traditional techniques around open fires. Meals are from a buffet, with shared tables. After lunch, there was Native American dancing performance on stage. Greg had seen the performance here many years ago, but it has changed since then. The performance now combines live dancing with AV going on a large screen behind the performers. This requires fewer people, but it worked. In 2009, Argosy  acquired the rights to Tillicum Village, so were no longer just providing the transportation to the island. It is a little on the expensive side for what they provide, but it is worth seeing once, especially if you have visitors from outside the Pacific Northwest. The food was good.

U.S.S. John C. Stennis near Bainbridge Island
headed to Bremerton.

This won't fit in my bath tub.

After the performance, we headed out. Winds were still light, but a hair stronger than the day before. The winds were still coming from the North, so we had to tack to get back toward the locks. We had to dodge a few ferries cutting between Seattle and Bremerton, and a few cruise ships were in the distance headed off to Alaska. But then Sandi said, "That's an aircraft carrier headed our way." Sandi had been in the Navy for 10 years, so knew an aircraft carrier when she saw one even from a long way off. Sure enough, coming South was a Nimitz class carrier, headed toward its home port in Bremerton.

The U.S.S. John C. Stennis (CVN 74), a 103,300 ton, nuclear powered supercarrier, was quite a sight as it steamed past us to the West. When you look at at a carrier like this on profile, especially from the stern, it does not look like the thing should be able to float. The tower, perched far out on one side makes it look like it should simply tip over. At one point, we had the aircraft carrier passing to our West, three cruise ships passing us from the East, headed north, and two ferries passing between Seattle and Bainbridge Island.

In the small lock headed in.

Stern view of the Stennis.

We dropped sail and made our way back through the locks without incident. As we approached the Fremont Bridge, we decided that we really need to have the bridge raised and gave the long-short signal with our air horn. The bridge attendant had us wait for a while, before raising the bridge. A terrific sense of power sets in as we mess up all the driver's commutes! We motored home and arrived just after sunset, using our new LED navigation lights for the first time. Waves in the lake were actually pretty heavy, as we had water splashing over our bow.

Raising the Fremont Bridge.

It was about as perfect a weekend as we could have hoped for, and the perfect trial for getting out of the lake and venturing forth. For next season, we will have to plan a more extensive trip in the San Juans.

Sail Tracks Using Garmin Chart Plotter

We went out for an evening sail with a co-worker of Sandi's. After getting under sail, we turned on our new Garmin 54dv chart plotter, which we got on sale online at West Marine. The wind was blowing East across the lake, allowing us to run both up and down the lake. We briefly chased another Catalina 22, sail number 15705, down the lake, but could not catch it.

The Garmin chart plotter recorded the track of where we went. We topped out at about 5 knots toward the end of the sail.

July 19th, 2016 Sail Track

We also tried out the transducer, a sonar emitter that came with the plotter. Greg had made a temporary frame to try it out of a 2x4 and hung over the transom of the boat. This was very cool to watch the lake bottom as we traveled.

We also got the chart plotter talking to the Standard Horizon VHF radio as a test. The VHF radio is able to retrieve the latitude and longitude from the chart plotter and broadcast that to other marine traffic using DSC (Digital Selective Calling). It is also able to retrieve that same information from other marine traffic and show them on the chart plotter. The combination of the chart plotter and the VHF is a safety issue; if the panic button on the VHF is pressed, it not only broadcasts a mayday with the MMSI of the vessel in trouble, but also the location of where the vessel is.

To get the sail track as an image, the track is downloaded onto a mini-SD card. That card is brought home and read into the Garmin Basecamp program. Basecamp then transfers the track to Google Earth. That map is then copied and pasted into Windows Paint, where it can be saved as a jpeg. That image is then uploaded here.

Let There Be Light

We worked toward finishing our DC panel wiring job. The though-deck connector got wired up.

We launched smoothly and motored for a bit down-lake, passing the barges that are carrying the disassembled old 520 bridge North for demolition. Then we raised sail.

As we were under sail, the connectors were put on the ends of the wires and connected to the fuse panel. Turned on the switches, and there was light and it was good! All that is left is to dress the wires so they are not hanging loose, and connect the VHF radio.

The new anchor light, steaming light, and deck light all worked. After docking, we added the navigation lights connection. All worked just like they were supposed to. All of the lights except the navigation lights are LED, so have minimal draw on the battery. We will replace those bulbs at a later point, so that we are all LED.

The sailing went smoothly. We found a few more rigging issues. We had added the spinnaker sheets, but, as usual, they were not rigged outside everything else. We did not raise the spinnaker, but we wanted them in place, if for no other reason than to get them out of the cabin. We got those routed correctly.

Our boat is running very nicely. We pulled in, and docked. Another nice day on the water.

First Sail Doctrine

We went out for our first sail of the season. Since we had disconnected all of our rigging to work on the mast, it took a while to get it all straightened out. A sail boat is a complicated machine. If any piece is out of place, it can jam up the works. We found that our jib sheets were not threaded through the blocks. We found halyards that were threaded on the wrong side of the spreaders. We are missing a knob that goes on the sail track stop (temporarily fixed with a nut and some anti-chafing tape). And other miscellaneous problems.

We were also missing the battens for the mainsail. After some running around, they were located. Do not lose your battens, as you cannot sail without them!

After finally getting all the pieces in place, we were ready to test the machine. We untied and launched, motoring out of the dock, dropped keel, and raised sails. Greg turned to Sandi and said, "Now do you remember why we did all this work?" It was magical being under sail for the first time this season.

Everything went smoothly as we sailed out on Lake Washington. We tacked, ran, and jibed very smoothly.

Sandi is having to learn how to read the wind. We have the new windex on the top of the mast, which makes reading the wind direction much easier than the yarn we had before. It does, however, have a disadvantage over the yarn, in that it does not give an indication of the strength of the wind. We had removed the yarn, but may put it back on for that purpose.

During the off-season, we had some work done on the mainsail at North Sails Seattle. They repaired a rip, and serviced the sail. While they were at it, they added new leech and luff tell-tales. Sandi is having to learn how to use them to trim the sail correctly.

After a couple of hours on the lake, at sunset we pulled back in without a problem, docked, tied up. Greg and Sandi worked on a few more things until it got too dark, such as adding the quick release to the back stay. Sandi accidentally tossing a screwdriver in the water. Greg managed to fish it out with a magnet on a line the next day.

Our leak from the volcano is not being a problem. We are getting maybe an ounce a day seeping through the connection. We will just mop up the water each time we are out, and wait until we are pulled out to replace the hardware. We need to do a bunch of work on the keel in the next off-season.

All in all, a great first sail of the season.

In the Water, Volcano Leak, and Cheap Bailer.

We finally got the boat in the water for the season. Well, maybe for the season. We launched, which went pretty smoothly. Since we had the mast off the boat, we had to get all the rigging back connected, which took a little more time than previous launches, but experience from previous launches compensated.

Quick-release toggle pin.

One thing we bought that makes it a little easier are some quick-release toggle pins. Use three of these to replace the pins that go into the chain plates, one for each of the forward shrouds, and one for the forestay (which is at the bottom of our furling jib). This makes it so that you are not fooling with cotter coils, which I hate messing with for anything that is not mostly permanent. They are a little pricey at the Catalina Direct web site, but they do make putting on the shrouds and forestay easier. The other shrouds stay connected to the boat when putting down the mast, unless the mast is removed from the boat.

We do need a technique for keeping the shrouds from getting caught on the snaps on the side of the cabin used for our cabin cover. The shroud gets under the snap, and gets a lot of tension as we raise the mast until we realize it is caught and pull it loose. This has happened each time we have raised the mast. We are considering our options here.

The crew and the mast raising system.

Our mast raising system rocks! We will get a detailed description here for it sometime soon. Greg had made a pretty good checklist for getting the mast raised, which makes sure that we do not forget any important step. (By the way, checklists are a good thing. If you want to learn about the value of checklists, read The Checklist Manifesto by Atul Gawande.)

After getting in the water, Sandi motored down to our summer moorage. Greg stored the trailer and unloaded all of the stuff like the gin pole and ladder back at the house and met Sandi just at sunset at the dock. Everything on the way down went smoothly, except the water in the bilge!

Captain at the helm.

Yes, after two seasons of a completely dry bilge, there was a little water. It is coming in at a pretty common place on a Catalina 22. There is a cable that extends from the keel winch through a keel cable tube and then through what is called the volcano. The volcano is a fiberglass cone that extends through the bottom of the boat to the keel. The keel cable tube is fitted to the volcano with two hose clamps. The seal between the tube and the volcano is seeping just a little, letting in water, about maybe a cup a day.

Fantasia arriving at the dock at sunset.

We ordered the parts from Catalina Direct to replace all the keel lifting hardware, including the cable and tube. However, you cannot replace the tube while the boat is in the water. The place where the tube meets the volcano is below the water line, and trying to remove it with the boat in the water will sink the boat! So to do this maintenance, we will have to pull the boat out. That should not be terrible as we do not have to put the mast down as we do the work...we just need some space at the boat launch to park for a while before we put it back in.

In the mean time, we will put on some Vaseline and wrap the joint in duct tape. That should slow the leak.

With the thought of having water in the boat, Greg made a hand bailer out of a milk jug.

Marine Adhesives

3M makes a variety of adhesives to be used on a boat. The three main ones are Marine Adhesive/Sealant 4000, 4200, and 5200. The 5200 comes in fast and slow cure. Essentially as the number goes up, the more permanent the adhesive. More permanent is not necessarily better, as you may need to remove that thing that you glued for maintenance some time in the future without stripping off the gelcoat.

Which one you should use is actually more complicated than just the adhesive strength, as it depends on what you are trying to adhere (wood to metal, metal to fiberglass, etc.), whether you need it in a color other than white, whether you need to use it below the waterline, etc.

There is a very nice chart of the 3M adhesive/sealants you should use for particular applications. We have a printed copy that we keep with the sealants. The 3M web site also has a similar chart. This article is also a good reference, and lists additional adhesives that may be useful, too, such as SikaFlex 291, 292, 295, and 296.

There is a stuff that will debond 5200. This describes how to use it.

Another terribly useful site when trying to figure out how to connect two items is This-to-That. You enter that you want to glue together glass to Styrofoam or ceramic to rubber, as examples, and it recommends the right glue for the job.

The Schooner Zodiac

We went out for a sail. It was another beautiful day for sailing, with about 12 knot winds and waves just starting to whitecap. The sun was out, but not blazing hot. There were far more sailboats out than power boats, with a few kayaks and kiteboarders out too. Our normal crew had the children replaced by a co-worker of Sandi's.

While tacking up the lake, we saw down by the 520 bridge a very large schooner, with two masts and four sails. We decided to go check it out, so started running down the lake, wing and wing, trying to catch it. It sailed over toward Kirkland, tacked, and then headed back toward the 520 bridge, we guessed back to Lake Union. It was going about twice as fast as us, so we gave up trying to catch it.

After getting home, we figured out what we were looking at. It was the schooner Zodiac, which has her home port in Bellingham. This is a 160 foot sailing ship, built in 1924 for the Johnson and Johnson brothers, of Band Aid fame. They sold it just before the stock market crashed. It eventually wound up as a pilot ship in San Francisco until 1972, ferrying the pilots for San Francisco bay out to the large ships. By 1974, it moved to Washington State.

Blue Angels at Seafair

Blue Angels in formation.

All six F/18s of the Blue Angels.

Every year since 1972, with a couple of exceptions, the Blue Angels have performed at Seafair. Seafair is a Seattle event, that includes parades, hydroplane races, marathons, and other activities. The most popular part of it, though, is the air show. The air show includes lots of different performances, but what everyone comes to see are the Blue Angels.

With the smoke on.

The Blue Angels are the U.S. Navy's flight demonstration squadron. They are a highly visible way of demonstrating Navy aircraft, their pilots and capabilities. The Navy considers them one of their primary recruiting tools. Considering how many people they reach and entertain, their $37 million annual budget does not seem excessive.

Since 1986, the Blue Angels have flown F-18/A/B/C/D Hornet aircraft. These are highly maneuverable, twin tailed fighter jets. The most modern jets in that class are F-18E/F Super Hornets. These are larger, but most of the reason for the upgrades are better avionics, weapon carrying capacity and fuel capacity, which would not help in an air show. The main difference between the air show aircraft and the military aircraft is a different flight stick, and the nose cannon has been replaced by the smoke generator. The Navy claims they can turn the Blue Angels F-18s into combat ready aircraft within 72 hours.

Blue Angels completing a loop
and about to be attacked by a giant dragonfly.

For Seafair, they come out and practice, then hold shows on Saturday and Sunday. They have to close the I-90 bridge for a couple of hours during the show. Also boat traffic is restricted from I-90 south.

All of them looping at once.

There are six aircraft in the show. Four aircraft fly together most of the time, while the two most experienced pilots fly more difficult maneuvers separately most of the time.

We went out for a sail to see them. We never got south of the 520 bridge, so most of the time they were quite a ways away. However, for a few maneuvers, they come pretty far north.

Kiteboarder on Lake Washington.

Sandi and Taylor.

Right after the show, there were about 100 powerboats all headed right for us. They had all been south of the 520 bridge and came through the eastern high-rise passage.

We stopped at Carilon Point in Kirkland for a break, then proceeded to tack back up the lake, watching the kite boarders. A very nice day of sailing.

Flying the Gennaker (Asymmetric Spinnaker) on the Catalina 22

Catalina 22 with the gennaker (asymmetric spinnaker) flying.

We went out for a sail with our Catalina 22 and flew our gennaker (asymmetric spinnaker) for the first time. Besides our normal crew, we took Sandi's oldest son, Devon, who shot all of the photos in this post.

We left about 3:30 p.m. and got back in about 7 p.m. For the first part of the sail, things went pretty typical. We headed north up the lake with the wind coming from the south. We attached the lines to the gennaker, and raised it. On the third try, after fixing various line problems, we finally got it up. We lifted the sock, and it was out flying. With a few adjustments, we got it taking the right shape.

We use the same halyard, sheets, and downhaul as the symmetric spinnaker (see July 4th posting), but the one new rigging item is the parrel beads. We got ours from Neil Pryde Sails. Parrel beads are a set of balls that go around the furling jib that allows the gennaker to move up and down and rotate without damaging it. We do need a way to keep the furling jib wound tight, though, to allow the beads to move.

Young bald eagle.

Circling around us was a young bald eagle, trying to fish. It was just getting its white head and tail. As mentioned in posts from last year, now there are quite a few bald eagles fishing on Lake Washington, and while the younger generation is used to seeing them, the older sailors view them like seeing a live dinosaur.

As we continued to sail, a beautiful C&C 41 came along side us. With so much more sail, we expected it to leave us in its wake, but with the gennaker out, we were keeping up.

We doused the gennaker and headed back south. The C&C 41, eventually caught up. The captain challenged us, but we had to wave as it sailed away.

C&C 41 sailing off.

Wind speeds and directions at Sand Point.
Modified from iWindSurf.

As we headed south, the wind picked up, and started radically changing directions. The chart of the wind speeds and directions around that time shows what we got ourselves into, with sustained winds of 2 to 12 mph, and gusting as high as 17. The wind was changing direction all over the place.

At one point, the wind radically changed direction, and gusted to 17 mph at the same time. It caught us unexpected, and Sandi had to fight a little to keep us under control. We finally headed into the dock. There were high waves, but the crew operated well and we got her docked.

A view from the deck.

Sailing to Lake Union

We went for our longest day of sailing yet. We set sail at about 12:30 with our normal crew of Conner, Taylor, Greg, and Sandi. The wind was coming from the south, and we headed in that direction, tacking down the lake. It was the wrong direction, however, for flying our spinnaker again.

Headed south in Lake Union. The Space Needle just
off the port bow.

After an couple of hours heading toward 520, we dropped sail and motored our way through the Lake Washington Ship Canal, the Montlake cut, Portage Bay, and into Lake Union. We passed under drawbridges that have enough clearance that they do not have to opened for us. We landed on the south end of Lake Union, and tied up to the dock there. Dinner was at Duke's Chowder House at Chandler's Cove.

Our route. The red line was our approximate path.
Map © OpenStreetMap contributors

The Lake Washington Ship Canal was a huge construction project completed between 1911 and 1934, creating a water passage between Puget Sound and Lake Washington, by way of Lake Union. Nothing like it would be allowed now because of the environmental impact, including dropping the water level in Lake Washington by almost nine feet. The Montlake Cut is a 110 foot wide man-made passage between Portage Bay and Lake Washington.

The crew. Fantasia tied up at Chandler's Cove.

After dinner, we reversed direction. While we were having dinner, the winds had shifted and were now coming from the north. We briefly put up the sails in Lake Union, then dropped them again. The Montlake Cut is too narrow to be sailing in, with many boats making their way from Lake Union and Puget Sound to Lake Washington. There were sailing classes with Lasers from Seattle Yacht Club in Portage Bay. There were sail boats from the University of Washington boat house. There were really inexperienced sailors trying their hardest to capsize a small sail boat and failing.

After we got back into Lake Washington, we raised sail and tacked our way north. The winds were just about perfect: strong, but not overwhelming. The sun had a slight haze over it, apparently from forest fires in British Columbia, which kept it a little cooler. There were lots of sailboats out, and only a few powerboats. The seas were too heavy for the power boats to pull shark bait behind them (what Greg calls kids on inflatables). For a while, we played with another Catalina 22. We nicknamed the captain Crazy Ivan, as he did things like take his boat in tight circles, or pull his boat ahead of ours on the same tack.

We pulled into the dock as the sun was headed near the horizon after 8 p.m. A long day, but one of the most enjoyable we have had sailing.

A Busy Day of Not Sailing: Mounting The Outhaul and Tiller Stay

Spring line to the concrete
post.

Whipping indicating where to tie up.

We did a lot more maintenance on the boat today.

We bought another snubber yesterday for our fifth dock line. This allows us to keep the boat nicely away from the dock in all directions. Our host moved a cleat for us on the dock, and the new position really helps. We also are whipping the dock lines to mark them at places so that we can very quickly get them adjusted just right when we pull in. This will make docking faster.

Pulpit eyes for spinnaker sheet blocks.

We put on new pulpit eyes on the stanchions for the spinnaker sheet blocks. Catalina Direct says that Catalina 22s have always used 1" thick tubing for the stern pulpit, but ours is made of 7/8" tubing. The pulpit eyes that we got were too large. They worked for our first time out, but we needed hardware that fits for a more permanent mounting. We found some hardware that will work at Fisheries Supply that fits the 7/8" tubing when used with a couple of D-shackles.

Blocks for the mainsail outhaul.

We mounted new blocks for the mainsail outhaul

Tiller stay.

And finally, we added our new tiller stay tiller controller. This was from a kit from Catalina Direct. They have several videos of projects to perform on a Catalina 22. The demo for installing this is on the Video Projects DVD volume 2. This allows the captain to leave the tiller for short periods without losing heading, as well as not having to fight the tiller so much. It also means that we do not have to tie up the tiller when we dock. It took us maybe two hours to install the whole thing. We did not do the complicated epoxy thing on the tiller.

Note that the video and directions are not clear on where to mount the fairleads that direct the line to the tiller. They say to mount them one inch inboard from the thingy on the side, but not how high off the seat. We mounted them just a little too low when the seat cushions are in place and will need to move them up an inch or so.

Flying the Symetrical Spinnaker on Fantasia

Our first time flying the spinnaker.

It has been Sandi's goal for quite some time that we would fly our symmetrical spinnaker on July 4th, Independence Day, of this year, for reasons that should be apparent from the accompanying pictures. It was looking like we were not going to get all the rigging in place until after the 4th, but everything came together and it worked.

This is a fairly big deal for us, because nobody on board has ever flown a spinnaker. All knowledge has been acquired by reading articles and books, and viewing videos online. (Possibly the best video on using the spinnaker is this one, Spinnaker Sailing, on YouTube.) We knew that there is some knowledge that you only get from actually doing something, so we were not sure that we even would make it work.

While still at dock, we checked our rigging and re-tensioned some stays. Also, a cleat had been moved for us on the dock to allow better tying up, so we adjusted our dock lines.

Before heading out, we planned on putting the spinnaker out on the port side. We planned that we would not bring out the jib until we were done with the spinnaker. So we fastened the turtle (spinnaker bag) to the life line on that side. We attached the snapshackles to the tack and clew of the spinnaker. Fortunately the port and starboard corners of the spinnaker are color coded.

For this season we are using the jib halyard to raise the spinnaker. For next season, we will probably add a head to the mast that has a separate ring and block just for the spinnaker. We have a furling jib, so the jib halyard is unused otherwise. We fastened the jib halyard to the top of the spinnaker sock. We tucked the jib sheets around the forward cleats so that they'd be low and out of the way.

We left the dock and motored out. We dropped the swing keel and raised the mainsail. Then we brought out the spinnaker pole and attached it to the mast ring. We attached the topping lift to the top of the spinnaker pole and the downhaul to the bottom and ran the port spinnaker sheet through the end of the spinnaker pole.

Spinnaker wrapped around the jib.

We then got ready and tried raising the spinnaker sock. First try failed as one of the lines was on the wrong side of the downhaul. Second try found another line interfering and had to be adjusted. Third try also failed, as we had failed to put the starboard spinnaker sheet around the front of the jib. Fourth try got the spinnaker sock to the top of the mast. The sock was lifted and the spinnaker started flying. There was not enough tension on the sheets though, and the spinnaker promptly wrapped itself around the jib! How do you solve that?

Turns out that if the slack is taken in on the sheets, and the helm varies a little off the wind, that enough wind catches the spinnaker to cause it to unwrap itself. And suddenly the spinnaker filled and was out flying! A little adjusting the sheets and downhaul and off we went, flying south down Lake Washington. The captain had to adjust to the fact that we had both the mainsail and spinnaker flying, but she soon figured that out.

Success!

Our spinnaker is red, white, and blue, which in the U.S. is very patriotic. We had people in power boats going by and blasting their horn!

After a very fast run down the lake toward Kirkland, we took down the spinnaker. Not completely without problems. The spinnaker sock did not want to come down. After a little head scratching, we figured out the problem: the sock lifting line was still cleated. You can pull on the line to bring it down as hard as you can and it will not budge when the lifting line is cleated!

The sock came down. Then the spinnaker came down and was folded back into the turtle. Unfastened the sheets and halyard, took it off the lifelines and down the forward hatch. The sheets and halyard get clipped to rings and stays to keep them from flopping around. We unfastened the spinnaker pole from the topping lift, downhaul, and mast ring, and stowed it below. Then we were ready to bring out the jib and tack back up the lake.

However, when the spinnaker wrapped itself around the jib, it messed up the furling of the jib and practically tied the jib sheets into knots. It took us a while to get that straightened out. After tacking back up, we pulled into the dock, exhausted but feeling very satisfied that all this work has paid off.

New Boom Topping Lift

Cup holder hooked on the life line.

This weekend, we were planning to sail, but spent the weekend working on the boat instead. We found a new favorite local supply store: Fisheries Supply. For sail boats, they have a better selection of parts than other local stores. Prices seem reasonable, and we do not have to wait for online orders. Harken products were on sale this weekend. We loaded up on the blocks and things we need for our topping lift and spinnaker and gennaker rigging.

We found some nice cup holders that fasten to the lifelines. We have been looking for something like them for a while.

Boom topping lift.

Sandi installed the rest of the new topping lift for the boom. We had installed the Catalina Direct D2180 wire topping lift before we put the mast up, but the line holding the boom was jury rigged. We now finished the job. Sandi screwed an eye strap on the aft port side of the boom. A Harken 224 micro-block was attached to the thimble on the end of the cable of the topping lift. Then a Harken 233 micro-cheek block was screwed on the starboard side of the aft portion of the boom. A Ronstan RF5101 V-cleat was screwed a little further forward on the starboard side of the boom. A 1/4" line is tied to the eye bolt on the port side, runs up through the block on the cable, then back to the cheek block on the starboard side and then forward to the cleat where it is tied off.

We actually don't like the Ronstan RF5101 V-cleat for this purpose as it does not seem to hold well, and will likely replace it with something else.

Last season we cheated by using the jib halyard as the topping lift. Since we have a furler, we are not using the the job halyard for its intended purpose. However, this season we expect to use it with the spinnaker, so we decided to do the topping lift the right way.

First Sail of the Season

Conner modeling his new personal
floatation device

New flares.

We took Fantasia out for the first sail of the season. Everything went smoothly, pulling out, tacking and coming back in. The crew is working pretty well together. The boat is good. The bald eagles were out fishing.

Distress flag.

Before this sail, we had acquired new safety gear. We have new flares for the flare gun. We have two more of the light self-inflating personal floatation devices. These were on sale at West Marine. We also got an emergency flag.

Put Fantasia in for the Season

We put Fantasia in for the season. Our hosts offered their dock again on Lake Washington. Putting her in was unusually undramatic. We connected up, trailered her to the boat launch, raised the mast in the parking lot (using our mast-raising system), backed it up and launched. It is almost like we knew what we were doing. The only mistake in the whole process was forgetting to release the tie down straps holding the boat to the trailer until the trailer was in the water. It does not float very well when those are still on. Greg had to wade out to release them. He learned from past mistakes, though, and removed the cell phone from his pocket before doing so!

We just motored to the dock and tied up. No sailing today.

New trim on the transom, just below the tiller and behind the rudder.

During the off-season, we fixed some things. There was an original trim piece on the transom that had completely disintegrated. We ordered a new one from Catalina Direct and put it on. The new one, however, did not fit around the existing hardware on the transom. Sandi used a Dremel tool to reshape it and drilled new holes in the plastic to fit the existing holes on the transom. It looks much better than the one that was there.

Before raising the mast, we attached a new cable topping lift for the boom to the mast. We removed the cotter pin to put it in place, but had to go get a replacement cotter pin. We promptly dropped it in grass and spent the next 20 minutes looking for it. We later got a bunch of cotter pins so that would be less annoying. Connecting the cable to the boom is just jury rigged for the moment, but we will fix that later.

The Boom Vang.

We have a new boom vang. The hardware already was in place for one on the mast and boom, but no blocks. We got a nice one from Catalina Direct, but you can just buy the Harken blocks and get some line. This will not save any money unless you can get the blocks on sale, though.

Our goal for this season is to get the gennaker and spinnaker flying. We have had them in the sail bags since we got the boat. It is unlikely they have ever flown over our boat, as our boat is missing the necessary rigging. The spinnaker was obviously bought used, as it has sail number for a different boat on it.

We are still figuring out the rigging necessary for the nylon sails. We bought a nice Forespar spinnaker pole, but currently there is no way to connect it to the mast. We also bought an ATF spinnaker sock. We will talk more about our spinnaker and gennaker rigging in later posts as we get them in place.

We are looking forward to another season of sailing.